Customer
Shopping Cart

Rode VideoMic Pro R

Manufacturer:
Rode
Our Part Number:
RDE1105
Manufacturer Part No:
VMPR
Backorder
Ship Time: Please LiveChat or Email For Time
Quick Overview
- Rycote® Lyre® shock mounting onboard
- All new capsule with lower noise and higher sensitivity
- Broadcast recording quality condenser microphone
- Compact form factor (150mm/6" length)
- Ultra lightweight (85g/3oz)
- 9V battery powered - over 70 hours use (alkaline)
- Integrated shock mounting & foam windscreen
- 3.5mm stereo mini-jack output (dual mono)
- Two step High Pass Filter (flat, 80Hz)
- Three position level control (-10dB, 0, +20dB)
- Camera shoe mount with 3/8" thread for easy boompole mounting
$229.00
Rode VideoMic Pro R Rode VideoMic Pro R
Rode VideoMic Pro R
Features:
  • Content
  • Rycote® Lyre® shock mounting onboard
  • All new capsule with lower noise and higher sensitivity
  • Broadcast recording quality condenser microphone
  • Compact form factor (150mm/6" length)
  • Ultra lightweight (85g/3oz)
  • 9V battery powered - over 70 hours use (alkaline)
  • Integrated shock mounting
  • Integrated foam windscreen
  • 3.5mm stereo mini-jack output (dual mono)
  • Two step High Pass Filter (flat, 80Hz)
  • Three position level control (-10dB, 0, +20dB)
  • Camera shoe mount with 3/8" thread for easy boompole mounting
  • 10 year warranty with online registration at www.rodemic.com/warranty

The RØDE VideoMic Pro is a true shotgun microphone designed for use with camcorders, DSLR cameras and portable audio recorders as a source of primary and reference audio.

At the heart of the VideoMic Pro is an all-new 1/2" condenser capsule that provides broadcast-quality audio via a 3.5mm minijack connector (outputting the mono signal to both left and right channels) with an incredibly low self-noise of just 14db. A super-cardioid polar pattern ensures that surrounding audio is minimised, and your recording is focused on the subject in front of the camera.

The integrated Rycote® Lyre® based shock mounting system separates the VideoMic Pro capsule and electronics from its mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone. Constructed from a single piece of hard-wearing thermoplastic, the Lyre® provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap.

Easily accessible on the rear face of the microphone are the power, filter and level controls. In addition to the microphone's native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.

Below these controls are the level settings, which attenuate or boost the recorded level as required. The -10dB level attenuation (or PAD) is ideal for recording loud sound sources, such as live music, motorsport, or interviews where the subject is very close to the camera. The +20dB level boost is designed for use with DSLR cameras, allowing the user to reduce the camera's preamp level (or mic-input level), effectively reducing the amount of noise generated by the camera's comparatively low quality audio circuitry.

The microphone uses a standard sized shoe mount for on camera use, and features a 3/8" thread in the base of the mount for easy boom pole mounting.

The VideoMic pro is battery powered, and provides over 70 hours recording from a single 9V battery.

The RØDE VideoMic is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Acoustic Principle
Line Gradient
Active Electronics
JFET impedance converter
Capsule
0.50"
Address Type
End
Frequency Range
40Hz - 20kHz(selected HPF @80)
Output Impedance
200Ω
Maximum SPL
134dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Maximum Output Level
6.9dBu (@ 1kHz, 1% THD into 1KΩ load
Sensitivity
-32.0dB re 1 Volt/Pascal (20.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted)
14dB-A
Weight
85gm
Dimensions
100mmH x 75mmW x 170mmD
Warranty
1 year with free extension to 10 years following registration

CA Proposition 65

Attention to all California residents, Proposition 65 or officially known as, the Safe Drinking Water and Toxic Enforcement Act of 1986, is a law that requires warnings be provided to California consumers when they might be exposed to chemicals identified by California as causing cancer or reproductive toxicity. The warnings are intended to help California consumers make informed decisions about their exposures to these chemicals from the products they use. The California Office of Environmental Health Hazard Assessment (OEHHA) administers the Proposition 65 program and publishes the listed chemicals, which includes more than 850 chemicals. August 2016, OEHHA adopted new regulations, to go into effect on August 30, 2018, which changes the information that is required in or on Proposition 65 warnings.

We want you to know and be aware of our product safety and Midwest Photo is taking all of the necessary steps to comply with the applicable safety and health requirements made by this Proposition 65.

WARNING: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

This disclaimer can be found on the product pages on our website under the Additional Information tab which appears below the product description. It is listed on all product pages to ensure that our customer is aware of the warnings put out by our suppliers so you can know the precautions before purchasing. 

Additional Information about Proposition 65

For background on the new Proposition 65 warnings, see https://www.p65warnings.ca.gov/new-proposition-65-warnings.

Proposition 65 and its regulations are posted at https://oehha.ca.gov/proposition-65/law/proposition-65-law-and-regulations.

To give Midwest Photo any notices of an alleged violation of the California Health and Safety Code Section 25249.5 or 25249.6, you must send us a notice at mpex@mpex.com.