Customer
Shopping Cart

Hive Lighting Wasp Hard Rolling Case

Manufacturer:
One Source
Our Part Number:
BEE1035
Manufacturer Part No:
HIVE-WPP-HC
Backorder
Ship Time: Please LiveChat or Email For Time
Quick Overview

- Built-in pull handle and wheels
- Ultra high-strength polypropylene copolymer resin
- UV, solvent, corrosion and fungus resistant (MIL-STD-810F)
- Complete gasket seal makes these cases absolutely watertight (MIL-STD-C-4150J)
- Resistant to corrosion and impact damage
- Continuous molded-in hinge
$379.05
Hive Lighting Wasp Hard Rolling Case
Hive Lighting Wasp Hard Rolling Case
Hive's Hard Case is designed for Hive Lighting's single light Bee and Wasp kits with custom designed foam inserts. The injection molded waterproof cases are constructed of ultra high-strength polypropylene copolymer resin and feature a gasketed, waterproof and airtight, submersible design (IP67) that is resistant to corrosion and impact damage. Its continuous molded-in hinge, patented "trigger release" latch system, comfortable, snap-down rubber over-molded cushion grip handle, secure stacking, and automatic ambient pressure equalization valve (MIL-STD-648C) all contribute to its military grade design.

• Built-in pull handle and wheels
• Ultra high-strength polypropylene copolymer resin
• UV, solvent, corrosion and fungus resistant (MIL-STD-810F)
• Complete gasket seal makes these cases absolutely watertight (MIL-STD-C-4150J)
• Automatic ambient pressure equalization value (MIL-STD-648C & IP67)
• Resistant to corrosion and impact damage
• Continuous molded-in hinge
• Patented "trigger release" latch system
• Rubber over-molded cushion grip handle
• Locking loop to accept a customer supplied lock
• Weight of Case Only: 14lbs
Interior Dimensions (L x W x D)
20.5 x 15.50 x 10.00 in (52.07 x 39.37 x 25.40 cm)
Exterior Dimensions (L x W x D)
22.25 x 18.75 x 12 in (56.52 x 47.63 x 30.48 cm)
Lid Depth
2.00 in (5.08 cm)
Base Depth
8.00 in (20.32 cm)

CA Proposition 65

Attention to all California residents, Proposition 65 or officially known as, the Safe Drinking Water and Toxic Enforcement Act of 1986, is a law that requires warnings be provided to California consumers when they might be exposed to chemicals identified by California as causing cancer or reproductive toxicity. The warnings are intended to help California consumers make informed decisions about their exposures to these chemicals from the products they use. The California Office of Environmental Health Hazard Assessment (OEHHA) administers the Proposition 65 program and publishes the listed chemicals, which includes more than 850 chemicals. August 2016, OEHHA adopted new regulations, to go into effect on August 30, 2018, which changes the information that is required in or on Proposition 65 warnings.

We want you to know and be aware of our product safety and Midwest Photo is taking all of the necessary steps to comply with the applicable safety and health requirements made by this Proposition 65.

WARNING: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

This disclaimer can be found on the product pages on our website under the Additional Information tab which appears below the product description. It is listed on all product pages to ensure that our customer is aware of the warnings put out by our suppliers so you can know the precautions before purchasing. 

Additional Information about Proposition 65

For background on the new Proposition 65 warnings, see https://www.p65warnings.ca.gov/new-proposition-65-warnings.

Proposition 65 and its regulations are posted at https://oehha.ca.gov/proposition-65/law/proposition-65-law-and-regulations.

To give Midwest Photo any notices of an alleged violation of the California Health and Safety Code Section 25249.5 or 25249.6, you must send us a notice at mpex@mpex.com.