Customer
Shopping Cart

Kupo Grip Arm Support

Manufacturer:
Kupo
Our Part Number:
KUP1006
Manufacturer Part No:
G200912
Backorder
Ship Time: Please LiveChat or Email For Time
Quick Overview
- Increases Load Capacity
- Kupo Tiny Clamp
- Designed for Kupo 3 & 4 Way Clamp System
- Extends from 22 - 30.7" (56 - 78cm)
- Quick Mounting
$65.75
Kupo Grip Arm Support
Kupo Grip Arm Support
The Kupo Grip Arm Support is a lightweight telescopic arm with a Kupo Tiny Clamp on one side designed to attach to the 5/8" (16mm) steel grip arm and a unique threaded stud notched specifically for the Kupo 3 & 4 Way Clamp System that mounts onto the riser of a Master C Stand.

Generally when you extend a large accessory such a flag or light fixture laterally past the center column of a C stand, the increased leverage may be too much for the grip head to bear. In the old days you could rectify this situation using another C stand as an additional support, or a combination of clamps, grip heads and grip arms.

Today Kupo has developed an innovative solution that rapidly mounts between both the riser section of a Master C Stand with help of either a Kupo 3 or 4 Way Clamp, and to a grip arm with the help of the included Kupo Tiny clamp already mounted on the other side of the Grip Arm Support. The Grip Arm Support has a built in ball joint that rotates 360 degrees for infinite flexibility and extends from 22 - 30.7" (56 - 78cm). With the addition of the Grip Arm Support, the load capacity at the end of your grip arm is greatly increased.

Features:
  • Increases Load Capacity
  • Kupo Tiny Clamp
  • Designed for Kupo 3 & 4 Way Clamp System
  • Extends from 22 - 30.7" (56 - 78cm)
  • Quick Mounting
Product Length
22.88" (58.1cm)
Product Width
2.43" (6.18cm)
Product Height
1.48" (3.75cm)
Product Weight
1.1 lbs (0.5kg)
Risers
1
Sections
2
Primary Material
Aluminum
Secondary Material
Stainless Steel Bolts
Minimum Jaw Diameter
0.08" (2mm)
Maximum Jaw Diameter
0.63" (16mm)

CA Proposition 65

Attention to all California residents, Proposition 65 or officially known as, the Safe Drinking Water and Toxic Enforcement Act of 1986, is a law that requires warnings be provided to California consumers when they might be exposed to chemicals identified by California as causing cancer or reproductive toxicity. The warnings are intended to help California consumers make informed decisions about their exposures to these chemicals from the products they use. The California Office of Environmental Health Hazard Assessment (OEHHA) administers the Proposition 65 program and publishes the listed chemicals, which includes more than 850 chemicals. August 2016, OEHHA adopted new regulations, to go into effect on August 30, 2018, which changes the information that is required in or on Proposition 65 warnings.

We want you to know and be aware of our product safety and Midwest Photo is taking all of the necessary steps to comply with the applicable safety and health requirements made by this Proposition 65.

WARNING: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

This disclaimer can be found on the product pages on our website under the Additional Information tab which appears below the product description. It is listed on all product pages to ensure that our customer is aware of the warnings put out by our suppliers so you can know the precautions before purchasing. 

Additional Information about Proposition 65

For background on the new Proposition 65 warnings, see https://www.p65warnings.ca.gov/new-proposition-65-warnings.

Proposition 65 and its regulations are posted at https://oehha.ca.gov/proposition-65/law/proposition-65-law-and-regulations.

To give Midwest Photo any notices of an alleged violation of the California Health and Safety Code Section 25249.5 or 25249.6, you must send us a notice at mpex@mpex.com.